An air conditioner, like a car, is a machine that must be serviced and maintained regularly. Even if an air conditioning system appears to be in good working order, routine maintenance and care are required to keep it operating as intended.
There are several fundamental reasons for servicing an air conditioner. Some benefits include improved performance, improved indoor air quality in North Richland Hills TX, reduced airborne viruses and bacteria spread, longer air conditioner life, and increased energy efficiency to save your energy.
You can do some things on your own to inspect and clean an air conditioner. The main advantage is that you will not need an Air Conditioner Repair in North Richland Hills.
1. Check Power
Before you begin most of the following tips or try anything else than turning air conditioners on/off or running AC units, it is crucial to ensure that your air conditioner does not run for power. Safety in the first place!
Take note of where the isolation switch is located. Because it is designed to isolate power to an air conditioning system, this switch is commonly referred to as an isolator. If you’re trying to test your air conditioner, make sure the isolator is turned on. The isolator, on the other hand, should be turned off for the majority of other checks.
Turn off all power sources to your air conditioning system, including the isolator, circuit breaker, and/or power outlet where an older unit may be plugged in. It’s better if you can turn off as many electrical points as possible.
Keep in mind that just because it’s turned off doesn’t mean the air conditioner isn’t working. Even when the AC units are turned off, invisibly faulty components, such as a broken isolator switch, can allow power to reach the AC units.
2. Check And Clean Filters
Air ducting enters a building by an indoor fan spiral, circulates, and is blown out in each room through outlets. The air is then retracted back into the air conditioning system and returned via the re-air grille to the indoor unit. Then the cycle begins again.
In the case of a duct system, this is particularly true.
The filter in a ducted system is usually found covering the return air grille in the ceiling. Given the airflow cycle, the filter’s cleanliness has an impact on the cleanliness of the air recycled indoors. A filter literally filters the air in your home, preventing the recirculation of airborne particles, dust, grime, and other pollutants. Dirt and mold can grow within the indoor unit if these particles are not captured by an adequately clean air conditioner filter and pass through to the indoor fan coil unit. Moldy air can then find its way into every room of the house or workplace.
How do you know if a filter needs to be cleaned? Holding a filter up to a light and seeing if you can see the light through it is a good rule of thumb. It’s time to clean the washable filter if the light is dim or, in the worst-case scenario, not visible at all. It’s time to replace it if it’s a disposable one.
3. Clean the Exterior of the Indoor Unit
Like any other surface in your home or business, the indoor air conditioner unit can collect dust, dirt, grime, cobwebs, and even mold. Wiping down the external unit with a feather duster, cloth, or lightly dampened washer is recommended regularly.
You can clean and sanitize the air conditioner with an antibacterial solution. Rather than spraying any liquid directly onto the air conditioner, spray a cloth first and then use that cloth to wipe down the casing.
Mold, dirt, and grime can accumulate inside the indoor unit, particularly on the fan barrel and coil. This can cause a moldy/musky odor, particle spitting from the indoor heat, and/or poor overall system performance due to reduced airflow.
They can be removed and cleaned chemically using specially designed equipment to remove internal build-up material. This is, however, a task best done by a professional Air Conditioner Installation Service in North Richland Hills. They are fully qualified air conditioner technicians with extensive knowledge of all technical and safety issues.
4. Check Temperatures
While the system is cooling, it’s worth checking the temperature difference between the supply and return air during an air conditioner service. The difference between the two temperatures should be as close to 10 degrees as possible. If not, run through the rest of the routine checks and retest. If the temperature difference is still less than 10 degrees, an HVAC contractor can look into it further.
To get the most accurate readings, use a calibrated thermometer to check temperatures. If the temperature isn’t right, it could be the thermometer, not the air conditioner.
The end of the thermometer must usually be as close as possible to airflow, irrespective of the way the air flows. Keep the air-flow thermometer for a proper period; for the digital thermometer 30-60 seconds or for the glass thermometer 7-10 minutes.
The supply air temperature for a ducted system can be obtained from air outlets in the ceiling, wall grilles, or floor vents. When accessing ceiling or wall registers, make sure you have a safe working platform and use extreme caution.
A temperature reading of the ducted return air grille and filter should be taken. Get as close to the return air as possible. Again, exercise caution when gaining access. You’ll essentially measure the ambient air condition if taken from a standing height away from the return air point.
The final takeaway is that you have to keep your HVAC system clean and running in a normal condition. While you get the Air conditioner or Heater Installation services in North Richland Hills TX, do not forget to get the manual instructions. Read them to know when and how to maintain the unit to avoid costly repairs.